(1/ 10 ) 2005- 08-05(ver.0.1) product information features (1) 14.1 sxga+(1400x1050 pixels) display size for notebook pc. (2) lvds interface system (h-sync, v-sync) mechanical specifications item specifications dimensional outline (typ.) 298.5 ( w ) x 226.5 ( h ) x 5.5max ( d ) mm number of pixels 1400 ( w ) x 1050 ( h ) pixels active area 285.6 ( w ) x 214.2 ( h ) mm viewing area 287.6 ( w ) x 216.2 ( h ) mm pixel pitch 0.204 ( w ) x 0.204 ( h ) weight (approximately) 325g backlight single ccfl, sidelight type absolute maximum ratings item min. max. unit ( v dd ) -0.3 4.0 v supply voltage ( v fl ) 0 2.0 kv(rms) fl driving frequency ( f fl ) (0) (100) khz input signal voltage ( v in ) -0.3 v dd +0.3 v operating ambient temperature *1 0 50 c operating temperature for panel *2 0 60 c storage temperature -20 60 c storage humidity (max. wet bulb temperature = 39 c) 10 90 %(rh) *1: wet bulb temperature should be 39 c max., and no condensation of water. *2: the surface temperature caused by self heat radiation of cell itself is specified on this item. electrical specification ( t a=25 c ) item min. typ. max. unit remarks ( v dd ) 3.0 3.3 3.6 v supply voltage ( v fl ) --- (625) --- v(rms) i fl =6.0ma(rms) fl start voltage 1550 --- --- v(rms) t a=0 c differential input voltage ( v id ) 100 --- 600 mv common mode input voltage ( v cm ) 1.0 --- 2.4-( v id )/2 v ( i dd ) *3 --- 380 --- ma current consumption ( i fl ) *4 2.0 --- 6.0 ma(rms) power consumption *1 *2 --- (5.0) --- w i fl =6.0ma(rms) *3 : refer to th63lvdf84a-85 specification by thine electronics, inc. *4: 8 color bars pattern *5: except the efficiency of fl inverter optical specification ( t a=25 c) item min. typ. max. unit remarks contrast ratio ( cr ) 100 250 --- --- ( t on ) --- --- 50 ms response time ( t off ) --- --- 50 ms luminance ( l ) --- 200 --- cd/m 2 i fl =6.0ma(rms) *the information contained herein is presented only as a guide for the applications of our products. no responsibility is assum ed by toshiba matsushita display technology or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of toshiba matsushita display technology or others. *the information contained herein may be changed without prior notice. it is therefore advisable to contact toshiba matsushita display technology before proceeding with the design of equipment incorporating this product. 36cm color tft-lcd module (14.1 type p-si tft) LTD141LM3S tentative toshiba matsushita displa y technolo gy co., ltd all information is subject to change without notice. please read bottom notes. www..net www..net
(2/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S dimensional outline (front) tentative unit : mm standard tolerance : 0.5 rea rsi de i/f- c n 30 226 .5 113 .1 149 .8 298 .5 }0.3 5.45 }0.3 45 }1 288 .7 57 .7 }1 198 .5 }0.3 198 .5 }0.3 b/l- c nm2 0.3 214 .2 2-3.1 }0.2 4- m2 5.5 max . 13 .85 }0.3 +0 .4 -0 .2 1 4.45 }0.3 229 .4max . 116 .2max . 2-3.1 }0.2 13 .85 }0.3 +0 .5 -0 .2 40 }7 80 }7 m2 max . 0.3 +0 .5 -0 .2 217 .3 216 .2 285 .6 287 .6 (beze l open ing ) (v ie w ing a rea : ) (a c t i ve a rea ) (a c t i v e a re a ) (v ie w ing a rea ) (beze l open ing ) jst : b hs r-02vs-1 jae : f i -xb 3 0s r- hf11a d ep th 2 .2 dep th 2 .2max . www..net www..net
(3/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S block diagram sequence of power supplies and signals circuit generation voltage manipulation gray scale converter dc/dc liquid crystal panel cn2 backlight x-driver y-driver cn1 connector panel controller lvds y-driver 1400 x 1050 pixels 0.2v 1 0 m s ( m a x . ) 3 . 0 v 3 . 0 v 4 0 m s ( m a x . ) 0 m s ( m i n . ) 4 0 m s ( m a x . ) 0 m s ( m i n . ) th tl os 0.2v 0.2v v v v 0 m s ( m i n . ) v v sfl fl 10% v sfl 10% v fl ( 5 0 0 m s ( m i n . ) ) ck+/- r0+/- r1+/- r2+/- dd v v flh 1 s e c ( m i n . ) 5 0 m s ( m a x . ) ( 2 5 0 m s ) ( m i n . ) www..net www..net
(4/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S timing chart tv tvw vsync tvsu tvhd th hsync tvfp tvbp tvd de 1049 1050 01 th thw hsync thbp thfp thds thd thblank de 1399 odd_pixel even_pixel 1400 nclk 13579 2468 10 www..net www..net
(5/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S timing specification 1) 2) 3) 4) 5) 6) 7) item symbol min. typ. max. unit horizontal scanning term t h 836 x t c 844 x t c 844 x t c - h-sync pulse width t hw 4 x t c - - - horizontal front porch t hfp 4 x t c - - - horizontal back porch t hbp 16 x t c - - - horizontal blanking term t hblank 136 x t c 144 x t c 144 x t c - horizontal display term t hd 700 x t c 700 x t c 700 x t c - frame period t v 1060 x t h 1066 x t h 1066 x t h - v-sync pulse width t vw 2 x t h - - - v-sync set up time (to h-sync) t vsu 8 x t c - - - v-sync hold time t vhd 8 x t c - - - vertical front porch t vfp 2 x t h - - - vertical back porch t vbp 6x t h - - - vertical display term t vd 1050 x t h 1050 x t h 1050 x t h clock period t c 17.544 18.519 19.597 ns note 1) refer to ?timing chart? and lvds (thc63lvdf 84a-85) specifications by thine electronic, inc.. note 2) if enab is fixed to "h" or "l" level for certain per iod while nclk is supplied, the panel displays black with some flicker. note 3) if nclk is fixed to "h" or "l" level for cert ain period while enab is supplied, the panel may be damaged. note 4) please adjust lcd operating signal timing and fl driving frequency, to optimize the display quality. there is a possibility that flicker is observed by the interference of lcd operating signal timing and fl driving condition (especially driving frequency), even if the condition satisfies above timing specifications and recommended operating conditions shown in 3. note5 ) do not make tv , tvdh and tvds fluctuate. if tv , tvdh , and tvds are fluctuate, the panel displays black. note6) in case of using the long frame period, the deter ioration of display quality, noise etc. may be occurred. note7) nclk count of each horizontal scanning time should be always the same. v-blanking period should be ? n ? x ?horizontal scanning time?. ( n : integer) frame period should be always the same. www..net www..net
(6/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S connector pin assignment for interface cn1 input signal (fi-xb30s*-hf** or fi-x30s-hf** / jae) [ mating connector :wire type fi-x30h(housing), fi-xc3-1-15000(contact) fpc type fi-x30m or fi-x30mr coax type fi-x30c or fi-x30c2(housing), fi-x30ch-7000(shell)] terminal no. symbol function assist terminal v ss gnd 1 v ss gnd 2 v dd power supply : +3.3v 3 v dd power supply : +3.3v 4 v edid ddc 3.3v power supply : +3.3v 5 nc non-connection 6 clkedid ddc clock 7 dataedid ddc data 8 rxoin0- negative lvds differential data input (odd), [r0-r5, g0] 9 rxoin0+ positive lvds differential data input (odd), [r0-r5, g0] 10 v ss gnd 11 rxoin1- negative lvds differential data input (odd), [g1-g5, b0-b1] 12 rxoin1+ positive lvds differential data input (odd), [g1-g5, b0-b1] 13 v ss gnd 14 rxoin2- negative lvds differential data input (odd), [b2-b5, hs, vs, de] 15 rxoin2+ positive lvds differential data input (odd), [b2-b5, hs, vs, de] 16 v ss gnd 17 rxoclkin- negative lvds differential clock input (odd) 18 rxoclkin+ positive lvds differential clock input (odd) 19 v ss gnd 20 rxein0- negative lvds differential data input (even), [r0-r5, g0] 21 rxein0+ positive lvds differential data input (even), [r0-r5, g0] 22 v ss gnd 23 rxein1- negative lvds differential data input (even), [g1-g5, b0-b1] 24 rxein1+ positive lvds differential data input (even), [g1-g5, b0-b1] 25 v ss gnd 26 rxein2- negative lvds differential data input (even), [b2-b5, hs, vs, de] 27 rxein2+ positive lvds differential data input (even), [b2-b5, hs, vs, de] 28 v ss gnd 29 rxeclkin- negative lvds differential clock input (even) 30 rxeclkin+ positive lvds differential clock input (even) assist terminal v ss gnd note 1) please connect gnd pin to ground. d on't use it as no-connect nor connection with high impedance. note 2) please connect nc to nothing. don't connect it to ground nor to other signal input. cn2 ccfl power source connector : bhsr-02vs-1 / japan solderless terminal mfg c o., ltd. mating connector : sm02b-bhs-1 / japan solderless terminal mfg co., ltd. terminal no. symbol function 1 v flh ccfl power supply ( high voltage) 2 v fll ccfl power supply (low voltage) www..net www..net
(7/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S recommended transmitter (thc63lvdf63a,thc63lvdm63a,thc63lvdm63a-85) to LTD141LM3S interface assignment case1: 6bit transmitter thc63lvdf63a,thc63lvdm63a,thc63lvdm63a-85 input terminal no. input signal (graphics controller output signal) LTD141LM3S interface (cn1) symbol terminal symbol function output signal symbol terminal symbol tin0 44 r0 red pixels display data (lsb) tin1 45 r1 red pixels display data tin2 47 r2 red pixels display data tin3 48 r3 red pixels display data tin4 1 r4 red pixels display data tin5 3 r5 red pixels display data (msb) tin6 4 g0 green pixels display data (lsb) tout0- tout0+ no.5 no.6 in0- in0+ tin7 6 g1 green pixels display data tin8 7 g2 green pixels display data tin9 9 g3 green pixels display data tin10 10 g4 green pixels display data tin11 12 g5 green pixels display data (msb) tin12 13 b0 blue pixels display data (lsb) tin13 15 b1 blue pixels display data tout1- tout1+ no.8 no.9 in1- in1+ tin14 16 b2 blue pixels display data tin15 18 b3 blue pixels display data tin16 19 b4 blue pixels display data tin17 20 b5 blue pixels display data (msb) tin18 22 hsync h-sync tin19 23 vsync v-sync tin20 25 de compound synchronization signal tout2- tout2+ no.11 no.12 in2- in2+ clk in 26 clk data sampling clock tclk out- tclk out+ no.14 no.15 clk- clk+ note 1) please connect nc pin to nothing. don' t connect it to ground nor to other signal input. g0 r5 r4 r3 r2 r1 r0 g5 b0 b1 g4 g1 b4 b5 g3 g2 b2 b3 in 0 in 1 in 2 tin4 tin3 tin2 tin1 tin0 tin13 t in 1 2 t in 1 1 t in 1 0 t in 9 t in 8 tin7 tin20 tin19 tin18 tin17 tin16 tin15 tin14 tin6 tin5 hsync vsync de www..net www..net
(8/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S recommended transmitter (thc63lvdf63a,thc63lvdm63a,thc63lvdm63a-85) to LTD141LM3S interface assignment case2: 8bit transmitter thc63lvdf63a,thc63lvdm63a,thc63lvdm63a-85 input terminal no. input signal (graphics controller output signal) LTD141LM3S interface (cn1) symbol terminal symbol function output signal symbol terminal symbol tin0 51 r0 red pixels display data (lsb) tin1 52 r1 red pixels display data tin2 54 r2 red pixels display data tin3 55 r3 red pixels display data tin4 56 r4 red pixels display data tin6 3 r5 red pixels display data (msb) tin7 4 g0 green pixels display data(lsb) tout0- tout0+ no.5 no.6 in0- in0+ tin8 6 g1 green pixels display data tin9 7 g2 green pixels display data tin12 11 g3 green pixels display data tin13 12 g4 green pixels display data tin14 14 g5 green pixels display data(msb) tin15 15 b0 blue pixels display data (lsb) tin18 19 b1 blue pixels display data tout1- tout1+ no.8 no.9 in1- in1+ tin19 20 b2 blue pixels display data tin20 22 b3 blue pixels display data tin21 23 b4 blue pixels display data tin22 24 b5 blue pixels display data (msb) tin24 27 hsync h-sync tin25 28 vsync v-sync tin26 30 de compound synchronization signal tout2- tout2+ no.11 no.12 in2- in2+ tin27 50 nc non connection (open) tin5 2 nc non connection (open) tin10 8 nc non connection (open) tin11 10 nc non connection (open) tin16 16 nc non connection (open) tin17 18 nc non connection (open) tin23 25 nc non connection (open) tout3- tout3+ clk in 31 clk data sampling clock tclk out- tclk out+ no.14 no.15 clk- clk+ note 1) please connect nc pin to nothing. don' t connect it to ground nor to other signal input. g0 r5 r4 r3 r2 r1 r0 g5 b0 b1 g4 g1 b4 b5 g3 g2 b2 b3 in 0 in 1 in 2 nc nc in 3 nc nc nc nc nc t in22 t in21 t in20 t in19 tin23 tin17 tin16 tin11 tin10 tin5 tin27 tin7 t in6 t in4 t in3 t in2 t in1 t in0 tin18 t in15 t in14 t in13 t in12 t in9 tin8 tin26 tin25 tin24 hsync vsync de www..net www..net
(9/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S 256k (k=1024) colors combination table display r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gray scale level black l l l l l l l l l l l l l l l l l l - blue l l l l l l l l l l l l h h h h h h - green l l l l l l h h h h h h l l l l l l - light blue l l l l l l h h h h h h h h h h h h - red h h h h h h l l l l l l l l l l l l - purple h h h h h h l l l l l l h h h h h h - yellow h h h h h h h h h h h h l l l l l l - basic color white h h h h h h h h h h h h h h h h h h - black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l l l l l l l l l 1 l l l l h l l l l l l l l l l l l l l 2 : : : : : : l3 l60 h h h h l h l l l l l l l l l l l l l61 dark light h h h h h l l l l l l l l l l l l l l62 gray scale of red red h h h h h h l l l l l l l l l l l l red l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l h l l l l l l l 1 l l l l l l l l l l h l l l l l l l l 2 : : : : : : l3 l60 l l l l l l h h h h l h l l l l l l l61 dark light l l l l l l h h h h h l l l l l l l l62 gray scale of green green l l l l l l h h h h h h l l l l l l green l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l l l l l l l h l 1 l l l l l l l l l l l l l l l l h l l 2 : : : : : : l3 l60 l l l l l l l l l l l l h h h h l h l61 dark light l l l l l l l l l l l l h h h h h l l62 gray scale of blue blue l l l l l l l l l l l l h h h h h h blue l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l h l l l l l h l 1 l l l l h l l l l l h l l l l l h l l 2 : : : : : : l3 l60 h h h h l h h h h h l h h h h h l h l61 dark light h h h h h l h h h h h l h h h h h l l62 gray scale of white & black white h h h h h h h h h h h h h h h h h h white l63 www..net www..net
(10/ 10 ) 2005- 08-05(ver.0.1) LTD141LM3S for safety lcd module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. in using our modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in engineering informati on no.ee-n001,"cautions and instructions for toshiba lcd modules". refer to individual specifications and technical data sheets (hereinafter called "td") for more detailed technical information. 1) special purposes a) toshiba matsushita display technology's standard lcd modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic. b) since toshiba matsushita display technology's standard lcd modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed toshiba matsushita display technology's published specification limits. c) in addition, since toshiba matsushita display technology standard lcd modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to traffic collision avoidance system and air traffic indicator), in milit ary defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) disassembling or modification do not disassemble or modify the module. it may damage sensitive parts inside lcd module, and may cause scratches or dust on the display. toshiba matsushita display technology doses not warrant the module, if customer disassembled or modified it. 3) breakage of lcd panel do not ingest liquid crystal material, do not inhale this material, and do not contact the material with skin, if lcd panel is broken and liquid crystal material spills out. if liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. if this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) glass of lcd panel be careful with chips of glass that may cause injuring fingers or skin, when the glass is broken. 5) electric shock disconnect power supply before handling lcd module. do not touch the parts inside lcd module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) absolute maximum ratings and power protection circuit do not exceed the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise lcd module may be damaged. employ protection circuit for power supply, whenever the specification or td specifies it. suitable protection circuit should be applied for each system design. 7) disposal when dispose lcd module, obey to the applicable environmental regulations. ! www..net www..net
|
